Fliteboard - Checklist

• Visual Inspection:
  • Check for any cracks, dents, or signs of wear that could lead to water ingress.
• Battery Lid Hinges Check:
  • Ensure they move smoothly. (Carefully apply WD-40 and wipe off any excess.)
• Battery Lid Latches Check:
  • Ensure that the screws are not loose and are securely tightened.
• Flitecell Battery Lid Seal:
  • Make sure it is free from sand and debris, and that there are no holes or tears anywhere.
• Receiver Plug Inspection:
  • Ensure there is no damage or corrosion. (Apply a cleaning agent and use a small brush if corrosion is present.)
• O-Ring Seal:
  • Ensure the orange O-ring between the Fliteboard and eFoil is properly seated and free from sand or debris. You may use compressed air or gently clean with a damp cloth.

• Motor Seal and Oil Service:
  • Ensure the initial service for the motor seal and oil was carried out after 6 months.
  • A service is required every 12 months or after 100 hours of use from the initial service. Contact your nearest service partner to schedule: Book a service
• All Plugs and Electrical Connections Check:
  • Ensure they are clean and free from corrosion, salt residue, or damage. (Use cleaning agent and a soft brush if corrosion is present.)
• All Screws and Threads Check:
  • Check for signs of corrosion; make sure Tef-Gel was applied when reattaching the wings (as per manual instructions).
• Sacrificial Anode Check:
  • Ensure the anode inside the wing is not excessively corroded. It should be replaced if damaged.
• Damage Inspection:
  • Check for any damage to the propeller, guard, wings, shims, mast, and Flitebox.
• Propeller Nut Check:
  • Make sure it is properly tightened. (Use 13mm socket wrench.)
• eFoil Mounting Torque:
  • Make sure the 4 x 20mm screws are torqued to 6 Nm. Refer to page 22 in the user manual.

• Refer to the 6-month Flitecell checklist.
• Fully charge your Flitecell at least 2 weeks before your first session for optimal balancing.

• Trigger Check:
  • Ensure the trigger moves freely. (Rinse off any grains of sand or debris using tap water.)
• Leash Check:
  • Inspect the leash for any signs of damage.
• Charging Contact Points Check:
  • Check all charging points including the charging cable. Ensure they are free from dirt and corrosion. (Use cleaning agent and a small brush if corrosion is present.)
• Charging Pins Check:
  • Ensure the charging pins on the cable move freely.
• Flitecell Charging:
  • Charge for 48 hours before the first use.

Fliteboard Update Checklist

• Connection Check:
  • Ensure all data connections are clean and corrosion-free before performing any updates. (Use cleaning agent and a small brush if needed.)
• Instructional Video:
  • Refer to our setup and function video here.
• Update:
  • Follow instructions to update your Board, eFoil, and Flite Controller to the latest specifications. Do not interrupt the process (e.g. power loss, incoming calls, messages, or leaving the update screen).
• Device Charging:
  • Ensure Flitecell, Flite Controller, and your iOS or Android device are sufficiently charged before updating.
• Network Connection:
  • Ensure you are in range of a strong data/Wi-Fi signal.

Power On

• Attach the eFoil drive to the board, connect the Flitecell, and turn on the power.

Dry Test

• Arm and run the motor on land for a maximum of 3 seconds in Gear 1.

If you notice any damage, significant corrosion, or are unable to connect during this check, please contact us at info@esurf.pl. Attach photos or videos showing the issue. We will get back to you as soon as possible!

Checklist complete.

We wish you a great season – see you on the water!